Deviation exposure
Visible duct debris found during an audit turns into a written deviation and a CAPA.
Pharmaceutical Manufacturing Facilities · Metro Atlanta, GA
Fire Damper, Grease Extraction & Life-Safety Compliance for Pharmaceutical Manufacturing Facilities | Certified HVAC Hygiene & Compliance
Regulatory compliance, operational continuity and verified air quality — delivered with zero disruption to your pharma plants operation in Metro Atlanta, GA. Certified crews, engineered containment, and a documented report at handover.
- IICRC-certified standards
- Certified biohazard technicians
- 24/7 rapid emergency response
- Video inspection included
Risks and compliance drivers in pharmaceutical manufacturing facilities
Pharma plants in Metro Atlanta, GA share a specific set of failure modes in their HVAC systems. Below are the four we are called about most, and the standards that govern how each one has to be corrected and documented.
Product cross-contamination
Shared air paths between suites move active ingredient dust where it does not belong.
Change-control friction
Work that is not documented in advance stalls at the quality gate.
Shutdown windows are short
Cleaning must finish inside a planned turnaround, not extend it.
| Standard | How it applies |
|---|---|
| IICRC-certified source removal | Documented source removal and post-clean verification. |
| ASHRAE 62.1 | Ventilation performance for manufacturing and support areas. |
| EPA-registered chemistry | Only labeled antimicrobials, with SDS and application logs supplied. |
| OSHA 1910 | Lockout/tagout, confined space and PPE compliance throughout. |
What compliance & fire safety includes
Fire and smoke damper inspection and testing, grease-bearing exhaust cleaning and life-safety documentation prepared for AHJ and insurer review.
- Damper-by-damper inspection, testing and tagging
- NFPA 96 grease extraction with access panels and hinge kits
- Deficiency list with photographs and location references
- Dated certificates and a compliance binder you can hand over
Our five-step field process
Every project follows the same sequence, whether it is one air handler or a full campus. Each step produces evidence that ends up in your handover report.
Fiber-optic & robotic camera inspection
Every system is filmed before a brush touches it. The baseline footage sets the scope, identifies damage and closed dampers, and becomes the first half of your before/after record.
Negative pressure containment & HEPA filtration
Work zones are isolated and held under negative pressure with HEPA-filtered machines, so debris leaves through the equipment instead of into the occupied building.
Mechanical agitation, brushing & vacuum extraction
Rotary brushes, air whips and compressed-air tools release bonded debris while the vacuum holds continuous capture — source removal, not surface dusting.
EPA-registered antimicrobial disinfection
Once the system is physically clean, labeled antimicrobial chemistry is applied to duct interiors, coils and pans, with product, dilution and dwell time logged.
Air quality audit & compliance report
Post-clean camera footage, airflow readings and particle counts are compiled into one report with technician credentials, standards applied and a floor-plan reference.
Pharma plants FAQ
Can you work inside a validated GMP environment?
Yes. We supply the protocol, materials list, SDS sheets and technician credentials ahead of time so your quality group can raise change control, then work to that approved protocol with sign-off at each step.
What happens if we find contamination mid-project?
Work stops in that zone, containment is extended, and we document the finding with photographs and location data before remediation continues. You get the finding in writing the same shift.
What documentation does our inspector actually want?
A dated record identifying each damper or hood by location, the condition found, the corrective action taken, and the technician who performed it. That is exactly the format of the binder we hand over.
What if a damper fails during testing?
It is photographed, logged as a deficiency with its location, and reported to you the same day. Repairs are quoted separately so nothing is done to life-safety equipment without your written approval.
Do you work nights, weekends and shutdowns?
Yes. Most commercial work in Metro Atlanta runs outside normal operating hours. We build the schedule around your occupancy and hand each area back clean and ready for use before your team returns.
More services for pharma plants
Compliance & Fire Safety in other sectors
- Compliance & Fire Safety for Hospitals
- Compliance & Fire Safety for Cleanrooms & labs
- Compliance & Fire Safety for Industrial plants
- Compliance & Fire Safety for Food processing
- Compliance & Fire Safety for Senior living
- Compliance & Fire Safety for Office towers
- Compliance & Fire Safety for Hotels
- Compliance & Fire Safety for Campuses
- Compliance & Fire Safety for Data centers